uu.seUppsala universitets publikationer
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Influence from surface roughness on steel transfer to PVD tool coatings in continuous and intermittent sliding contacts
Uppsala universitet, Teknisk-naturvetenskapliga vetenskapsområdet, Tekniska sektionen, Institutionen för teknikvetenskaper, Tillämpad materialvetenskap. (Tribomaterial)
Uppsala universitet, Teknisk-naturvetenskapliga vetenskapsområdet, Tekniska sektionen, Institutionen för teknikvetenskaper, Tillämpad materialvetenskap. (Tribomaterial)
Dalarna University.
Primateria AB, Uppsala.
Visa övriga samt affilieringar
2012 (Engelska)Ingår i: Tribology International, ISSN 0301-679X, E-ISSN 1879-2464, Vol. 56, s. 9-18Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

A sliding test is used in order to evaluate the influence of tool surface roughness on the material transfer in intermittent and continuous sliding of PVD coated HSS against case hardening steel (20NiCrMo2). Two cutting tool coatings, TiN and AlCrN, and three different surface roughnesses are tested. For polished surfaces the same types of material transfer are obtained irrespective of sliding mode and coating type. If the surfaces are too rough, the tribofilms do not grow thick enough to separate the surfaces and the work material is abrasively worn in both sliding modes. With increased sliding distance, cracking of the TiN coating occurs while the AlCrN coating remains intact.

Ort, förlag, år, upplaga, sidor
2012. Vol. 56, s. 9-18
Nyckelord [en]
Transfer, coating, sliding, roughness
Nationell ämneskategori
Materialteknik
Forskningsämne
Teknisk fysik med inriktning mot materialvetenskap
Identifikatorer
URN: urn:nbn:se:uu:diva-167054DOI: 10.1016/j.triboint.2012.06.013ISI: 000308284000002OAI: oai:DiVA.org:uu-167054DiVA, id: diva2:480626
Forskningsfinansiär
VINNOVATillgänglig från: 2012-01-19 Skapad: 2012-01-19 Senast uppdaterad: 2017-12-08Bibliografiskt granskad
Ingår i avhandling
1. On Transfer of Work Material to Tools
Öppna denna publikation i ny flik eller fönster >>On Transfer of Work Material to Tools
2012 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

Bulk forming and cutting are widely used to shape metals in industrial production. Bulk forming is characterized by large strains, extensive plastic deformation and large surface expansions. Cutting is characterized by high speeds, high pressures and high temperatures. The prevailing conditions during these processes lead to transfer of work material to tools. In bulk forming this is a significant problem. The transferred work material is hardened and becomes harder than the work material, causing galling. This leads to high friction and high forming forces, bad surface finish of the formed products and significant difficulties to produce complicated geometries. In cutting, transfer of work material can be desired for protection of the tool surface. However, the transfer film has to be of the correct type to provide a stable and predictive behaviour during operation.

In this thesis the influence from tool material and surface treatment on work material transfer has been studied for both applications, with the use of simplified laboratory test methods followed by extensive surface studies. Both the tendency to, appearance of and chemical composition of work material transfer is evaluated. The results are compared with real industrial examples, to ensure that the correct mechanisms are mimicked.

In forming, the problems arise when poor lubrication prevails, due to high forming forces or large surface expansions. The transfer of work material can then be avoided with the use of a galling resistant coating, offering low adhesion. However, the coating has to be as smooth as possible, to avoid activation of the work material and subsequent transfer.

In cutting, the desired transfer film can be obtained by choosing the correct cutting parameters. The geometry and material of the fabricated component is often predetermined, setting the general cutting conditions, but the cutting speed influences the formation of the transfer film. Too low speed or too high speed leads to an unstable cutting process and poor surface finish of the piece. The speed intervals for each mechanism are partly determined by the tool material and thus by the tool coating.

Ort, förlag, år, upplaga, sidor
Uppsala: Acta Universitatis Uppsaliensis, 2012. s. 68
Serie
Digital Comprehensive Summaries of Uppsala Dissertations from the Faculty of Science and Technology, ISSN 1651-6214 ; 894
Nyckelord
Tribology, Friction, Forming, Cutting, Galling, Material transfer, Tribological coatings, Surface finish, Micro mechanisms, Aluminium
Nationell ämneskategori
Teknik och teknologier
Forskningsämne
Materialvetenskap
Identifikatorer
urn:nbn:se:uu:diva-165828 (URN)978-91-554-8261-9 (ISBN)
Disputation
2012-03-02, Häggsalen, Lägerhyddsvägen 1, Uppsala, 10:15 (Svenska)
Handledare
Tillgänglig från: 2012-02-10 Skapad: 2012-01-10 Senast uppdaterad: 2013-04-08
2. Tribology at the Cutting Edge: A Study of Material Transfer and Damage Mechanisms in Metal Cutting
Öppna denna publikation i ny flik eller fönster >>Tribology at the Cutting Edge: A Study of Material Transfer and Damage Mechanisms in Metal Cutting
2012 (Engelska)Doktorsavhandling, sammanläggning (Övrigt vetenskapligt)
Abstract [en]

The vision of this thesis is to improve the metal cutting process, with emphasis on the cutting tool, to enable stable and economical industrial production while using expensive tools such as hobs. The aim is to increase the tribological understanding of the mechanisms operating at a cutting edge and of how these can be controlled using different tool parameters. Such understanding will facilitate the development and implementation of future, tribologically designed, cutting tools.

Common wear and failure mechanisms in gear hobbing have been identified and focused studies of the material transferred to the tool, in both metal cutting operations and in simplified tribological tests, have been conducted. Interactions between residual stresses in the tool coating and the shape of the cutting edge have also been studied.

It was concluded that tool failure is often initiated via small defects in the coated tool system, and it is necessary to eliminate, or minimize, these defects in order to manufacture more reliable and efficient gear cutting tools. Furthermore, the geometry of a cutting edge should be optimized with the residual stress state in the coating, in mind. The interaction between a compressive stress and the geometry of the cutting edge will affect the stress state at the cutting edge and thus affect the practical toughness and the wear resistance of the coating in that area.

An intermittent sliding contact test is presented and shown to be of high relevance for studying the interaction between the tool rake face and the chip in milling. It was also demonstrated that material transfer, that can have large effects on the cutting performance, commences already after very short contact times. The nature of the transfer may differ in different areas on the tool. It may include glassy layers, with accumulations of specific elements from the workpiece, and transfer of steel in more or less oxidized form. Both tool coating material, its surface roughness, and the relative speed between the tool surface and the chip, may influence the extent to which the different transfer will occur.

Ort, förlag, år, upplaga, sidor
Uppsala: Acta Universitatis Upsaliensis, 2012. s. 77
Serie
Digital Comprehensive Summaries of Uppsala Dissertations from the Faculty of Science and Technology, ISSN 1651-6214 ; 988
Nyckelord
Tribology, Metal cutting, Gear hobbing, Wear, Coating, Residual stress, Material transfer, Steel
Nationell ämneskategori
Teknik och teknologier
Forskningsämne
Teknisk fysik med inriktning mot tribomaterial
Identifikatorer
urn:nbn:se:uu:diva-183186 (URN)978-91-554-8514-6 (ISBN)
Disputation
2012-12-07, 2005, Ångströmlaboratoriet, Lägerhyddsvägen 1, Uppsala, 10:15 (Svenska)
Handledare
Tillgänglig från: 2012-11-16 Skapad: 2012-10-23 Senast uppdaterad: 2013-01-23Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Personposter BETA

Heinrichs, JannicaGerth, JuliaWiklund, Urban

Sök vidare i DiVA

Av författaren/redaktören
Heinrichs, JannicaGerth, JuliaWiklund, Urban
Av organisationen
Tillämpad materialvetenskap
I samma tidskrift
Tribology International
Materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 946 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf