uu.seUppsala universitets publikationer
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Experimental and theoretical study of the microscopic crater wear mechanism in titanium machining
Sandvik Coromant R&D, Sweden.
Sandvik Coromant R&D, Sweden.
Sandvik Coromant R&D, Sweden.
Uppsala universitet, Teknisk-naturvetenskapliga vetenskapsområdet, Tekniska sektionen, Institutionen för teknikvetenskaper, Fasta tillståndets fysik.
Visa övriga samt affilieringar
2017 (Engelska)Ingår i: Wear, ISSN 0043-1648, E-ISSN 1873-2577, Vol. 376, s. 115-124Artikel i tidskrift (Refereegranskat) Published
Abstract [en]

Continuous turning of Ti6AI4V with uncoated WC-Co cutting tool inserts mainly results in crater wear on the rake face of the tool. The crater is located close to the cutting edge and increases in size with increased time in cut. The flank wear remains minor until the point when the crater reaches a critical size so that the edge deforms plastically and edge breakage occurs. To understand the crater wear degradation mechanisms, this study focuses on examining the worn tool at different stages, using both experimental and theoretical techniques, as well as under static and dynamic conditions. A layer of adhered work-piece material is observed in the crater. The present study shows both experimental and theoretical evidence of carbon depletion of the WC in the crater and formation of W (bcc) at the interface during wet continuous longitudinal turning of Ti6AI4V. This has been demonstrated for the first time. In addition, indications of a carbon rich compound, possibly MC, where M=Ti, V and W, are also observed. These observations are verified by simulation of the diffusion process. Furthermore, diffusion simulations indicate that a liquid may form at the tool/chip interface in the crater zone during machining. Turning is a dynamic process, however, to study the chemical driving forces in this system under static conditions, a means of verification of which phases will form is needed. Therefore, a diffusion couple consisting of the same materials is prepared and analyzed. Similar results are obtained for the diffusion couple as for the worn tool, indicating that the chemical wear is an important degradation parameter. The diffusion couple results are also compared to a numerical simulation of the diffusion process.

Ort, förlag, år, upplaga, sidor
2017. Vol. 376, s. 115-124
Nyckelord [en]
Ti6Al4V, Turning, Craterwear, Tungsten, X-ray Diffraction, Diffusion simulations
Nationell ämneskategori
Materialteknik
Identifikatorer
URN: urn:nbn:se:uu:diva-329129DOI: 10.1016/j.wear.2017.01.104ISI: 000403904000016OAI: oai:DiVA.org:uu-329129DiVA, id: diva2:1148916
Konferens
21st International Conference on Wear of Materials (WOM), MAR 26-30, 2017, Long Beach, CA
Tillgänglig från: 2017-10-12 Skapad: 2017-10-12 Senast uppdaterad: 2017-10-12Bibliografiskt granskad

Open Access i DiVA

Fulltext saknas i DiVA

Övriga länkar

Förlagets fulltext

Personposter BETA

Johansson, MalinNorgren, Susanne

Sök vidare i DiVA

Av författaren/redaktören
Johansson, MalinNorgren, Susanne
Av organisationen
Fasta tillståndets fysikTillämpad materialvetenskap
I samma tidskrift
Wear
Materialteknik

Sök vidare utanför DiVA

GoogleGoogle Scholar

doi
urn-nbn

Altmetricpoäng

doi
urn-nbn
Totalt: 109 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf