uu.seUppsala universitets publikationer
Ändra sökning
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf
Identification of extreme load cases for a surface drill rig by means of MBS simulations
Uppsala universitet, Teknisk-naturvetenskapliga vetenskapsområdet, Matematisk-datavetenskapliga sektionen, Institutionen för informationsteknologi, Avdelningen för teknisk databehandling.
2010 (Engelska)Självständigt arbete på avancerad nivå (yrkesexamen), 20 poäng / 30 hpStudentuppsats (Examensarbete)
Abstract [en]

This master thesis is Atlas Copco Craelius’ first step in incorporating numericalmethods in load case analysis during the development process. Atlas Copco needs toconstantly evolve and refine their methods in the design process to remain as thenumber one manufacturer of mining and construction equipment. Poor knowledge ofloads results either in structural failures or in oversized structures, both very costlyfor Atlas Copco.The main goal of this thesis is to examine the potential in MBS software by using it toidentify extreme load cases in one of Atlas Copco Craelius’ surface drill rigs, Mustang5. The MBS-software ADAMS View is used to build a model of the Mustang 5 drill rigand evaluate simulation results. The rig model is subject to motions which representreal case scenarios. The feed positioning possibilities are examined thoroughly since it was expected that the positioning has impact on the load levels. 25 different feedpositioning are simulated.The main conclusion is that the load levels are highly dependent on the feedpositioning. For example, the load levels in the boom raising cylinder can increaseseven times, if the rig is operated with the most unfavorable positioning compared tothe recommended. It could also be concluded that not only one positioning isextreme in terms of loads; it depends on which part of the boom system is beingobserved. Thus, several positioning cases have to be taken into consideration in orderto optimize the design of parts in the boom system.

Ort, förlag, år, upplaga, sidor
2010. , s. 46
Serie
UPTEC F, ISSN 1401-5757 ; 10 050
Nyckelord [en]
mbs, mbd, dynamic, load, loads, atlas copco
Identifikatorer
URN: urn:nbn:se:uu:diva-130228OAI: oai:DiVA.org:uu-130228DiVA, id: diva2:348981
Uppsök
teknik
Handledare
Examinatorer
Tillgänglig från: 2010-09-08 Skapad: 2010-09-04 Senast uppdaterad: 2010-09-08Bibliografiskt granskad

Open Access i DiVA

fulltext(1283 kB)831 nedladdningar
Filinformation
Filnamn FULLTEXT01.pdfFilstorlek 1283 kBChecksumma SHA-512
e36a1631314068adef7753a55267bc70533acd7638d7413c3f00a0b38e9bbb20ff345b7079a27b5409d8436053d4da4c61bc556182bab2340e4c053f35df7308
Typ fulltextMimetyp application/pdf

Sök vidare i DiVA

Av författaren/redaktören
Anbo, Anders
Av organisationen
Avdelningen för teknisk databehandling

Sök vidare utanför DiVA

GoogleGoogle Scholar
Totalt: 831 nedladdningar
Antalet nedladdningar är summan av nedladdningar för alla fulltexter. Det kan inkludera t.ex tidigare versioner som nu inte längre är tillgängliga.

urn-nbn

Altmetricpoäng

urn-nbn
Totalt: 856 träffar
RefereraExporteraLänk till posten
Permanent länk

Direktlänk
Referera
Referensformat
  • apa
  • ieee
  • modern-language-association
  • vancouver
  • Annat format
Fler format
Språk
  • de-DE
  • en-GB
  • en-US
  • fi-FI
  • nn-NO
  • nn-NB
  • sv-SE
  • Annat språk
Fler språk
Utmatningsformat
  • html
  • text
  • asciidoc
  • rtf