uu.seUppsala University Publications
Change search
ReferencesLink to record
Permanent link

Direct link
Ion Tracks Developed in Polyimide resist on Si wafers as template for nanowires
Uppsala University, Teknisk-naturvetenskapliga vetenskapsområdet, Technology, Department of Engineering Sciences.
2005 In: Nuclear Instruments and Methods in Physics Research B, Vol. 240, 681-689 p.Article in journal (Refereed) Published
Place, publisher, year, edition, pages
2005. Vol. 240, 681-689 p.
URN: urn:nbn:se:uu:diva-94960OAI: oai:DiVA.org:uu-94960DiVA: diva2:168994
Available from: 2006-10-13 Created: 2006-10-13Bibliographically approved
In thesis
1. Nanopatterning by Swift Heavy Ions
Open this publication in new window or tab >>Nanopatterning by Swift Heavy Ions
2006 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

Today, the dominating way of patterning nanosystems is by irradiation-based lithography (e-beam, DUV, EUV, and ions). Compared to the other irradiations, ion tracks created by swift heavy ions in matter give the highest contrast, and its inelastic scattering facilitate minute widening and high aspect ratios (up to several thousands). Combining this with high resolution masks it may have potential as lithography technology for nanotechnology. Even if this ‘ion track lithography’ would not give a higher resolution than the others, it still can pattern otherwise irradiation insensitive materials, and enabling direct lithographic patterning of relevant material properties without further processing. In this thesis ion tracks in thin films of polyimide, amorphous SiO2 and crystalline TiO2 were made. Nanopores were used as templates for electrodeposition of nanowires.

In lithography patterns are defined by masks. To write a nanopattern onto masks e-beam lithography is used. It is time-consuming since the pattern is written serially, point by point. An alternative approach is to use self-assembled patterns. In these first demonstrations of ion track lithography for micro and nanopatterning, self-assembly masks of silica microspheres and porous alumina membranes (PAM) have been used.

For pattern transfer, different heavy ions were used with energies of several MeV at different fluences. The patterns were transferred to SiO2 and TiO2. From an ordered PAM with pores of 70 nm in diameter and 100 nm inter-pore distances, the transferred, ordered patterns had 355 nm deep pores of 77 nm diameter for SiO2 and 70 nm in diameter and 1,100 nm deep for TiO2. The TiO2 substrate was also irradiated through ordered silica microspheres, yielding different patterns depending on the configuration of the silica ball layers.

Finally, swift heavy ion irradiation with high fluence (above 1015/cm2) was assisting carbon nanopillars deposition in a PAM used as template.

Place, publisher, year, edition, pages
Uppsala: Acta Universitatis Upsaliensis, 2006. 48 p.
Digital Comprehensive Summaries of Uppsala Dissertations from the Faculty of Science and Technology, ISSN 1651-6214 ; 229
Materials science, swift heavy ions, lithography, nanopatterning, self-assembly, Materialvetenskap
urn:nbn:se:uu:diva-7183 (URN)91-554-6676-1 (ISBN)
Public defence
2006-11-03, Siegbahns Salen, The Ångstöm Laboratory, Lägerhyddsvägen, Uppsala, 09:30
Available from: 2006-10-13 Created: 2006-10-13Bibliographically approved

Open Access in DiVA

No full text

By organisation
Department of Engineering Sciences

Search outside of DiVA

GoogleGoogle Scholar
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Total: 162 hits
ReferencesLink to record
Permanent link

Direct link