uu.seUppsala University Publications
Change search
ReferencesLink to record
Permanent link

Direct link
X-ray micro-computed tomography investigation of fibre length degradation during the processing steps of short-fibre composites
Uppsala University, Disciplinary Domain of Science and Technology, Technology, Department of Engineering Sciences, Applied Mechanics.
Uppsala University, Disciplinary Domain of Science and Technology, Technology, Department of Engineering Sciences, Applied Mechanics.
2014 (English)In: Composites Science And Technology, ISSN 0266-3538, Vol. 105, 127-133 p.Article in journal (Refereed) Published
Place, publisher, year, edition, pages
2014. Vol. 105, 127-133 p.
Keyword [en]
Polymer-matrix composites (PMCs), . Microstructures, Injection moulding, X-ray tomography
National Category
Mechanical Engineering
URN: urn:nbn:se:uu:diva-229209DOI: 10.1016/j.compscitech.2014.10.011ISI: 000346943400016OAI: oai:DiVA.org:uu-229209DiVA: diva2:736187
Available from: 2014-08-05 Created: 2014-08-05 Last updated: 2015-02-02Bibliographically approved
In thesis
1. Structure and Mechanical Behaviour of Wood-Fibre Composites
Open this publication in new window or tab >>Structure and Mechanical Behaviour of Wood-Fibre Composites
2014 (English)Doctoral thesis, comprehensive summary (Other academic)
Abstract [en]

Wood fibres have several advantages compared to man-made synthetic fibres: they have high specific stiffness, are renewable, relatively inexpensive, available in industrial quantities and biodegradable. However, to increase and diversify their utilisation, it is necessary to increase the understanding on what controls their mechanical properties.

In this work, the hygroelastic behaviour of isolated wood fibres has been investigated using an analytical model and a finite element model based on three dimensional images obtained using synchrotron-based X-ray micro-computed tomography. It was thus possible to show how the cell wall responds to a mechanical load or a change in ambient relative humidity.

The wood fibres were then mixed with a biopolymer aiming to produce a cost-efficient, 100% renewable composite material. The microstructure of the produced composites has been characterised using X-ray microtomography and digital image processing. It was for instance possible to measure the moisture-induced swelling of fibres embedded in a polymeric matrix. The experimental results have then been successfully compared with prediction obtained with a finite element model. The length of the fibres inside the composite has also been measured from three dimensional images, aiming to understand how each step of the processing chain is affecting the degradation of the aspect ratio of the reinforcing fibres.

The presence of defects inside the composite has also been quantified using X-ray microtomography. The effects of the defects on the tensile strength have been predicted using an analytical model. The results have been compared with the measured tensile strength on each sample, showing that the size and orientation of the critical defect controls the tensile strength of the material.

Finally, wood-fibre mats without any matrix material were compressed in the chamber of a microtomographic scanner. Sequential images were taken during the test. Using digital volume correlation, it was possible to calculate the local strain field inside the material. The effects of heterogeneities on the strain field have then been investigated. The applied compressive load resulted in transport of material from high to low density regions.

Place, publisher, year, edition, pages
Uppsala: Acta Universitatis Upsaliensis, 2014. 34 p.
Digital Comprehensive Summaries of Uppsala Dissertations from the Faculty of Science and Technology, ISSN 1651-6214 ; 1158
National Category
Applied Mechanics
urn:nbn:se:uu:diva-229290 (URN)978-91-554-8988-5 (ISBN)
Public defence
2014-09-19, Ångström 4001, Lägerhyddsvägen 1, Uppsala, 10:00 (English)
Available from: 2014-09-15 Created: 2014-08-05 Last updated: 2015-01-22

Open Access in DiVA

No full text

Other links

Publisher's full texthttp://www.sciencedirect.com/science/article/pii/S026635381400373X

Search in DiVA

By author/editor
Joffre, ThomasGamstedt, E. Kristofer
By organisation
Applied Mechanics
In the same journal
Composites Science And Technology
Mechanical Engineering

Search outside of DiVA

GoogleGoogle Scholar
The number of downloads is the sum of all downloads of full texts. It may include eg previous versions that are now no longer available

Altmetric score

Total: 432 hits
ReferencesLink to record
Permanent link

Direct link