Logo: to the web site of Uppsala University

Inherently antibacterial materials could be an effective method to reduce the spread and impact of bacterial infections when incorporated into healthcare settings. The aim of this study was to examine whether additively manufactured PVDF-graphene nanoplatelet composites could confer antibacterial effects. The composites and reference filaments were produced with thermal compounding extrusion, which is a scalable method commonly used in industry, and were successfully printed using fused filament fabrication. The composites reduced bacterial attachment by 21 % and 81 % within the first hour of exposure for Escherichia coli and Staphylococcus aureus respectively, when graphene flakes were exposed on the surface of the samples. E. coli strains were also examined for biofilm formation on the developed materials, but no additional antibacterial effect was seen, most likely because of the limited exposure of the graphene nanoplatelets on the surface of the samples. It was found that the surface topology resulting from different printing configurations, as well as the exposure time to bacteria had a significant influence on the biological response to the samples.

Poorly soluble drugs represent a substantial portion of emerging drug candidates, posing significant challenges for pharmaceutical formulators. One promising method to enhance the drug’s dissolution rate and, consequently, bioavailability involves transforming them into an amorphous state within mesoporous materials. These materials can then be seamlessly integrated into personalized drug formulations using Additive Manufacturing (AM) techniques, most commonly via Fused Deposition Modeling. Another innovative approach within the realm of AM for mesoporous material-based formulations is semi-solid extrusion (SSE). This study showcases the feasibility of a straightforward yet groundbreaking hybrid 3D printing system employing SSE to incorporate drug-loaded mesoporous magnesium carbonate (MMC) into two different drug formulations, each designed for distinct administration routes. MMC was loaded with the poorly water-soluble drug ibuprofen via a solvent evaporation method and mixed with PEG 400 as a binder and lubricant, facilitating subsequent SSE. The formulation is non-aqueous, unlike most pastes which are used for SSE, and thus is beneficial for the incorporation of poorly water-soluble drugs. The 3D printing process yielded tablets for oral administration and suppositories for rectal administration, which were then analyzed for their dissolution behavior in biorelevant media. These investigations revealed enhancements in the dissolution kinetics of the amorphous drug-loaded MMC formulations. Furthermore, an impressive drug loading of 15.3 % w/w of the total formulation was achieved, marking the highest reported loading for SSE formulations incorporating mesoporous materials to stabilize drugs in their amorphous state by a wide margin. This simple formulation containing PEG 400 also showed advantages over other aqueous formulations for SSE in that the formulations did not exhibit weight loss or changes in size or form during the curing process post-printing. These results underscore the substantial potential of this innovative hybrid 3D printing system for the development of drug dosage forms, particularly for improving the release profile of poorly water-soluble drugs.

Fused deposition modeling (FDM) and selective laser sintering (SLS) are two of the most employed additive manufacturing (AM) techniques within the pharmaceutical research field. Despite the numerous advantages of different AM methods, their respective drawbacks have yet to be fully addressed, and therefore combinatorial systems are starting to emerge. In the present study, hybrid systems comprising SLS inserts and a two-compartment FDM shell are developed to achieve controlled release of the model drug theophylline. Via the use of SLS a partial amorphization of the drug is demonstrated, which can be advantageous in the case of poorly soluble drugs, and it is shown that sintering parameters can regulate the dosage and release kinetics of the drug from the inserts. Furthermore, via different combinations of inserts within the FDM-printed shell, various drug release patterns, such as a two-step or prolonged release, can be achieved. The study serves as a proof of concept, highlighting the advantages of combining two AM techniques, both to overcome their respective shortcomings and to develop modular and highly tunable drug delivery devices.

The incorporation of drug-loaded mesoporous materials in dosage forms prepared with fused deposition modeling (FDM) has shown the potential to solve challenges relating to additive manufacturing techniques, such as the stability of poorly-soluble drugs in the amorphous state. However, the addition of these non-melting mesoporous materials significantly affects the mechanical properties of the filament used in FDM, which in turn affects the printability of the feedstock material. Therefore, in this study a full-factorial experimental design was utilized to investigate different processing parameters of the hot melt extrusion process, their effect on various mechanical properties and the potential correlation with the filaments' printability. The thermolabile, poorly-soluble drug ibuprofen was utilized as a model drug to assess the potential of two mesoporous materials, Mesoporous Magnesium Carbonate (MMC) and a silica-based material (MCM-41), to thermally protect the loaded drug. Factorial and principal components analysis displayed a correlation between non-printable MCM-41 filaments and their mechanical properties where printable filaments had a maximum stress >7.5 MPa and a Young's modulus >83 MPa. For MMC samples there was no clear correlation, which was in large part attributed to the filaments' inconsistencies and imperfections. Finally, both mesoporous materials displayed a thermal protective feature, as the decomposition due to the thermal degradation of a significant portion of the thermolabile drug was shifted to higher temperatures post-loading. This highlights the potential capability of such a system to be implemented for thermosensitive drugs in FDM applications.

Silicon nitride (Si3N4) is a promising biomaterial, currently used in spinal fusion implants. Such implants should result in high vertebral union rates without major complications. However, pseudarthrosis remains an important complication that could lead to a need for implant replacement. Making silicon nitride implants more bioactive could lead to higher fusion rates, and reduce the incidence of pseudarthrosis. In this study, it was hypothesized that creating a highly negatively charged Si3N4 surface would enhance its bioactivity without affecting the antibacterial nature of the material. To this end, samples were thermally, chemically, and thermochemically treated. Apatite formation was examined for a 21-day immersion period as an in-vitro estimate of bioactivity. Staphylococcus aureus bacteria were inoculated on the surface of the samples, and their viability was investigated. It was found that the thermochemically and chemically treated samples exhibited enhanced bioactivity, as demonstrated by the increased spontaneous formation of apatite on their surface. All modified samples showed a reduction in the bacterial population; however, no statistically significant differences were noticed between groups. This study successfully demonstrated a simple method to improve the in vitro bioactivity of Si3N4 implants while maintaining the bacteriostatic properties.