Logo: to the web site of Uppsala University

uu.sePublications from Uppsala University
Change search
Link to record
Permanent link

Direct link
Publications (10 of 14) Show all publications
Haque, M. F., Malik, T., Ahmed, H., Khan, H. R., Arshad, K., Assaleh, K. & Johansson, T. (2026). A Combined Aliasing-Free Outphasing Transmitter. IEEE Access, 14, 45676-45688
Open this publication in new window or tab >>A Combined Aliasing-Free Outphasing Transmitter
Show others...
2026 (English)In: IEEE Access, E-ISSN 2169-3536, Vol. 14, p. 45676-45688Article in journal (Refereed) Published
Abstract [en]

This paper presents a mobile communication transmitter architecture that exploits band-limited pulse-width modulation (BL-PWM) combined with outphasing to eliminate aliasing and image distortions. The proposed combined outphasing-aliasing free PWM transmitter (COAF-PWMT) shows very high linearity and high power efficiency as it can use switch-mode power amplifiers (SMPAs) or linear power amplifiers operating at peak power. The transmitter is implemented using two 130 nm CMOS class-D power amplifiers and experimentally validated with both 1.5 MHz LTE signals and 10 MHz 5G NR signals at a carrier frequency of 700 MHz. Experimental results for the 1.5 MHz LTE signal show that the COAF-PWMT achieves an ACLR of 54.3 dBc and an average efficiency of 15.7%. The architecture improves ACLR by 22.6 dB and power efficiency by 4.4% compared to the aliasing-free PWM transmitter (AF-PWMT). It also provides a 14.3 dB ACLR and 2.2% efficiency boost over the Gibbs-phenomenon-reduced aliasing-free PWM transmitter (GR-AFPWMT), and a 15.0 dB ACLR improvement over the modified aliasing-free PWM transmitter (MAF-PWMT). Compared to the aliasing-compensated PWM transmitter (AC-PWMT), the COAF-PWMT increases ACLR by 19.5 dB with similar efficiency. For the 10 MHz 5G NR signal, the COAF-PWMT reaches an ACLR of 42 dB, which is 6 dB better than the GR-AFPWMT, and improves efficiency by 1.6%. These results show the COAF-PWMT's promise for highly linear and efficient RF transmitter design in future wireless systems.

Place, publisher, year, edition, pages
Institute of Electrical and Electronics Engineers (IEEE), 2026
Keywords
Pulse width modulation, Radio transmitters, Distortion, Linearity, Power harmonic filters, Power amplifiers, Radio frequency, Batteries, Dynamic range, Band-pass filters, Carrier-based PWM, aliasing distortion, image distortion, aliasing-free PWM, linear PA, switched-mode PA (SMPA), outphasing
National Category
Signal Processing Other Electrical Engineering, Electronic Engineering, Information Engineering Telecommunications
Identifiers
urn:nbn:se:uu:diva-584402 (URN)10.1109/ACCESS.2026.3676452 (DOI)001727225100006 ()2-s2.0-105034414877 (Scopus ID)
Available from: 2026-04-17 Created: 2026-04-17 Last updated: 2026-04-17Bibliographically approved
Ul Haque, M. F., Ahmed, H. & Johansson, T. (2026). All-digital aliasing-free PWM transmitter with reduced filtering requirements. Scientific Reports, 16, Article ID 9235.
Open this publication in new window or tab >>All-digital aliasing-free PWM transmitter with reduced filtering requirements
2026 (English)In: Scientific Reports, E-ISSN 2045-2322, Vol. 16, article id 9235Article in journal (Refereed) Published
Abstract [en]

The paper presents an All-Digital Aliasing-Free PWM (AF-PWM) transmitter, which combines multiphase band-limited PWM (MP-BLPWM) and accumulated N phase-shift pulse modulation (AN-PSPM), and its FPGA-implementation. As the architecture is based on MP-BLPWM, which generates finite harmonics PWM, this eliminates image and aliasing distortion, and improves spectral performance. However, finite harmonics PWM leads to large amplitude variation, which is converted to two voltage level signals using AN-PSPM, leading toward all-digital implementation. The transmitter's performance is experimentally validated for 5G-NR and LTE signals, both with and without a switched-mode power amplifier (Class-D PA). Measurement results demonstrate that, when used with the PA, the transmitter achieves ACLR values of 37.9 dBc for 5G-NR and 42.2 dBc for LTE signals. Furthermore, the EVM of the proposed transmitter with the Class-D PA is measured at 1.3% for 5G-NR and 0.9% for LTE, highlighting its effectiveness for advanced wireless communication applications.

Place, publisher, year, edition, pages
Springer Nature, 2026
National Category
Signal Processing
Identifiers
urn:nbn:se:uu:diva-583875 (URN)10.1038/s41598-026-44436-1 (DOI)001718268900006 ()41844785 (PubMedID)2-s2.0-105033462443 (Scopus ID)
Funder
Uppsala University
Available from: 2026-04-07 Created: 2026-04-07 Last updated: 2026-04-07Bibliographically approved
Zhang, S.-L., Johansson, T., Yao, Y. & Wu, D. (2026). Prospects of Quantum Computing. SmartSys, 2(2), Article ID e70026.
Open this publication in new window or tab >>Prospects of Quantum Computing
2026 (English)In: SmartSys, ISSN 2097-5430, Vol. 2, no 2, article id e70026Article in journal, Editorial material (Other academic) Published
Abstract [en]

It has been anticipated that quantum computing (QC) would solve computational tasks involving quantum phenomena intractable for supercomputers based on digital technology. Concurrently, however, the vast development of artificial intelligence (AI) has resulted in systems targeting these real-world problems with unprecedented progress including protein design for drug discovery and constituent optimizations for novel magnetic materials. Even climate simulation has welcomed the AI era. This “News and Views” intends to provide an analysis of QC for future applications and associated technological challenges. Our analysis leads to a scenario in which room-temperature QC technology acts as an energy-efficient processor for large-system computations likely targeting markets for mobile systems. With this scenario, silicon nanofabrication would contribute indispensably to further advancing QC technology in all aspects.

Place, publisher, year, edition, pages
John Wiley & Sons, 2026
National Category
Other Electrical Engineering, Electronic Engineering, Information Engineering
Identifiers
urn:nbn:se:uu:diva-590098 (URN)10.1002/sys3.70026 (DOI)
Funder
Vinnova, 2024-00436Swedish Research Council, 2021-06025
Available from: 2026-06-15 Created: 2026-06-15 Last updated: 2026-06-15Bibliographically approved
Engstrand, J., Johansson, T., Karlsson, R. L. & Augustine, R. (2025). 120 Mb/s Fat-Intrabody Communication (Fat-IBC). In: 2025 55th European Microwave Conference (EuMC): . Paper presented at 55th European Microwave Conference (EuMC), Utrecht, Netherlands, September 23-25, 2025 (pp. 660-663). Institute of Electrical and Electronics Engineers (IEEE)
Open this publication in new window or tab >>120 Mb/s Fat-Intrabody Communication (Fat-IBC)
2025 (English)In: 2025 55th European Microwave Conference (EuMC), Institute of Electrical and Electronics Engineers (IEEE), 2025, p. 660-663Conference paper, Published paper (Refereed)
Abstract [en]

Fat-intrabody communication (Fat-IBC) enables wireless communication through human fat tissue, which acts as a low-loss channel for microwave signals. This study demonstrates data rates exceeding 120 Mb/s through a 30 cm phantom at 2.45 GHz using commercially available IEEE 802.11n hardware. Three antenna configurations were evaluated: in-body to in-body, in-body to on-body, and on-body to on-body. The results show that the in-body to in-body configuration achieves the longest range, potentially up to 70 cm, at 120 Mb/s. The on-body to on-body setup reaches at least 43 cm at over 32 Mb/s, which is a typical data rate requirement for brain-machine interfaces. This makes Fat-IBC a competitive solution for high-speed intrabody communication compared to alternative techniques such as galvanic and capacitive coupling. Future improvements include optimizing antennas and addressing regulatory constraints, such as specific absorption rate limits. The findings are relevant for medical implants and wearable devices requiring robust wireless communication within the human body.

Place, publisher, year, edition, pages
Institute of Electrical and Electronics Engineers (IEEE), 2025
Keywords
wireless communication, wireless lan, wlan, phantom, fat tissue, fat-intrabody communication, fat-ibc
National Category
Communication Systems
Identifiers
urn:nbn:se:uu:diva-574576 (URN)10.23919/EuMC65286.2025.11235144 (DOI)001832896900148 ()2-s2.0-105029580395 (Scopus ID)978-2-87487-081-1 (ISBN)979-8-3315-1260-6 (ISBN)
Conference
55th European Microwave Conference (EuMC), Utrecht, Netherlands, September 23-25, 2025
Funder
Swedish Foundation for Strategic Research, FUS21-0067
Available from: 2026-01-06 Created: 2026-01-06 Last updated: 2026-09-08Bibliographically approved
Mehboob, R., Haque, M. F., Malik, T. & Johansson, T. (2025). A novel IFPWM‐based all‐digital transmitter architecture and FPGA implementation. International journal of circuit theory and applications, 53(1), 466-476
Open this publication in new window or tab >>A novel IFPWM‐based all‐digital transmitter architecture and FPGA implementation
2025 (English)In: International journal of circuit theory and applications, ISSN 0098-9886, E-ISSN 1097-007X, Vol. 53, no 1, p. 466-476Article in journal (Refereed) Published
Abstract [en]

The software-defined radio (SDR) concept for wireless communications provides flexibility and simplicity, replacing most of the analog air interfaces. With all-digital transmitters (ADT), the entire signal chain, from user input to frequency upconversion, can be implemented in the digital (programmable) domain, making it an ideal platform for SDR. ADTs depend heavily on the bitrate of the serializer to generate a specific frequency band with good Adjacent Channel Leakage Ratio (ACLR), however, the transmission frequency achieved is lower than half of the serializer's bitrate.In this paper, we present a scalable ADT architecture capable of generating higher transmission frequencies with state-of-the-art comparable ACLR and relatively low implementation complexity. A modified Pulse-Width Pulse-Position Modulation (M-PWPM) scheme, based on the RF-PWM principle, is derived, which provides an improved ACLR and Error Vector Magnitude (EVM). The proposed transmitter architecture implemented on an Field-Programmable Gate Array (FPGA) achieves ACLR of 32 dB and EVM below 2% at 14.72 GHz Tx frequency for a 20 MHz LTE signal. The obtained transmission frequency was achieved using a serializer operating at 28 Gbps, which is for the first time beyond the half of the serializer's bitrate. The proposed ADT architecture has the potential to be used with serializers beyond 28 Gbps bitrate, hence, achieving even higher transmission frequencies.

In an ADT, the entire signal chain, from user input and baseband processing to frequency up-conversion, is in the digital domain, providing significant advantages over transmitters having analog front-end. In this paper, we present an ADT architecture employing heterodyne principle that achieves a transmission frequency beyond half of the serializer bit-rate and show its implementation on an FPGA having a serializer bit-rate of upto 28 Gbps. image

Place, publisher, year, edition, pages
John Wiley & Sons, 2025
Keywords
all-digital transmitter (ADT), FPGA, IF-PWMT, MGT, M-PWM, RF-PWMT
National Category
Other Electrical Engineering, Electronic Engineering, Information Engineering
Identifiers
urn:nbn:se:uu:diva-549227 (URN)10.1002/cta.4123 (DOI)001246014900001 ()2-s2.0-85196109257 (Scopus ID)
Available from: 2025-01-31 Created: 2025-01-31 Last updated: 2025-02-03Bibliographically approved
Johansson, T. (2025). Bokrecension: Halvledaråldern - kemin bakom dagens teknik [Review]. Elektroniktidningen
Open this publication in new window or tab >>Bokrecension: Halvledaråldern - kemin bakom dagens teknik
2025 (Swedish)In: Elektroniktidningen, ISSN 1102-7495Article, book review (Other (popular science, discussion, etc.)) Published
Abstract [sv]

Corona har i alla fall haft det positiva med sig att allmänheten snappat upp ordet halvledare och att det är viktigt för att Volvo ska kunna bygga bilar. Men det är fortfarande ganska svårt att förklara vad en halvledare är och varför vi har blivit så beroende av dem. Tänk om man kunde rekommendera en lättläst bok om ämnet på svenska, skriver Ted Johansson om den nya boken av Linköpingsprofessorn Henrik Pedersen.

Place, publisher, year, edition, pages
Stockholm: , 2025
National Category
Other Electrical Engineering, Electronic Engineering, Information Engineering
Research subject
Chemistry
Identifiers
urn:nbn:se:uu:diva-564094 (URN)
Available from: 2025-07-23 Created: 2025-07-23 Last updated: 2025-07-23
Rathod, K. N., Datt, G., Aslibeiki, B., Johansson, T., Barucca, G., Peddis, D., . . . Sarkar, T. (2025). Interface-Induced Synaptic Performance in CeO2/La0.8Ba0.2MnO3 Oxygen Reservoir Junction. ACS Applied Materials and Interfaces, 17(51), 69666-69675
Open this publication in new window or tab >>Interface-Induced Synaptic Performance in CeO2/La0.8Ba0.2MnO3 Oxygen Reservoir Junction
Show others...
2025 (English)In: ACS Applied Materials and Interfaces, ISSN 1944-8244, E-ISSN 1944-8252, Vol. 17, no 51, p. 69666-69675Article in journal (Refereed) Published
Abstract [en]

Realizing next-generation intelligent applications requires novel resistive switching devices that can operate with low power, high stability, and desired neuromorphic performance. La0.8Ba0.2MnO3 (LBMO), a functional complex oxide exhibiting a room-temperature metal-insulator transition, shows promise in this context. In this work, we demonstrate interface-engineered resistive switching in the LBMO thin film junction by introducing an ultrathin CeO2 insertion layer. Compared to bare LBMO film, which requires higher forming voltages and suffers from limited stability and large cycle-to-cycle variability, the CeO2/LBMO (LBC) device exhibits stable, low-power bipolar resistive switching. The LBC device achieves a low forming voltage of 2.2 V, an ON/OFF ratio of similar to 102, endurance of 600 switching cycles, and data retention of 103 seconds. The improved performance is attributed to controlled oxygen vacancy migration and redistribution facilitated by the CeO2 interlayer. Furthermore, the LBC device displays, for the first time, bioinspired synaptic behaviors, such as gradual potentiation and depression under pulsed stimuli, and exhibits linear plasticity under nonidentical pulse schemes, effectively emulating synaptic weight modulation. Our results demonstrate an interface-induced resistive switching device as a compelling candidate for next-generation neuromorphic components.

Place, publisher, year, edition, pages
American Chemical Society (ACS), 2025
Keywords
manganite, oxygen vacancy, interfaceengineering, memristor, synapse, potentiation, depression, neuromorphic
National Category
Condensed Matter Physics Other Electrical Engineering, Electronic Engineering, Information Engineering Materials Chemistry
Identifiers
urn:nbn:se:uu:diva-583042 (URN)10.1021/acsami.5c19731 (DOI)001635382700001 ()41367176 (PubMedID)2-s2.0-105025709947 (Scopus ID)
Funder
Wenner-Gren Foundations, UPD2022-0006EU, European Research Council, 101002772Swedish Research Council Formas, 2023-01607Knut and Alice Wallenberg Foundation, 2022.0079Swedish Research Council FormasEU, European Research Council
Available from: 2026-03-31 Created: 2026-03-31 Last updated: 2026-03-31Bibliographically approved
Rangaiah, P., Engstrand, J., Johansson, T., Perez, M. D. & Augustine, R. (2024). 92 Mb/s Fat-Intrabody Communication (Fat-IBC) With Low-Cost WLAN Hardware. IEEE Transactions on Biomedical Engineering, 71(1), 89-96
Open this publication in new window or tab >>92 Mb/s Fat-Intrabody Communication (Fat-IBC) With Low-Cost WLAN Hardware
Show others...
2024 (English)In: IEEE Transactions on Biomedical Engineering, ISSN 0018-9294, E-ISSN 1558-2531, Vol. 71, no 1, p. 89-96Article in journal (Refereed) Published
Abstract [en]

The human subcutaneous fat layer, skin and muscle together act as a waveguide for microwave transmissions and provide a low-loss communication medium for implantable and wearable body area networks (BAN). In this work, fat-intrabody communication (Fat-IBC) as a human body-centric wireless communication link is explored. To reach a target 64 Mb/s inbody communication, wireless LAN in the 2.4 GHz band was tested using low-cost Raspberry Pi single-board computers. The link was characterized using scattering parameters, bit error rate (BER) for different modulation schemes, and IEEE 802.11n wireless communication using inbody (implanted) and onbody (on the skin) antenna combinations. The human body was emulated by phantoms of different lengths. All measurements were done in a shielded chamber to isolate the phantoms from external interference and to suppress unwanted transmission paths. The BER measurements show that, except when using dual on-body antennas with longer phantoms, the Fat-IBC link is very linear and can handle modulations as complex as 512-QAM without any significant degradation of the BER. For all antenna combinations and phantoms lengths, link speeds of 92 Mb/s were achieved using 40 MHz bandwidth provided by the IEEE 802.11n standard in the 2.4 GHz band. This speed is most likely limited by the used radio circuits, not the Fat-IBC link. The results show that Fat-IBC, using low-cost off-the-shelf hardware and established IEEE 802.11 wireless communication, can achieve high-speed data communication within the body. The obtained data rate is among the fastest measured with intrabody communication.

Place, publisher, year, edition, pages
Institute of Electrical and Electronics Engineers (IEEE), 2024
Keywords
Body area networks (BAN), body sensor networks (BSN), intrabody communication (IBC), bit error rate (BER), signal-to-noise ratio (SNR), WLAN
National Category
Communication Systems
Identifiers
urn:nbn:se:uu:diva-515092 (URN)10.1109/tbme.2023.3292405 (DOI)001129696100032 ()37432837 (PubMedID)
Funder
EU, Horizon 2020, 965044
Available from: 2024-01-22 Created: 2024-01-22 Last updated: 2026-02-01Bibliographically approved
Yang, Y., Khaksaran, M. H., An, J. B., Lee, S., Kim, H. J., Johansson, T., . . . Zhang, S.-L. (2024). Phototransistors of Engineered InGaZnO Channel for Specific Molecular Detection in the Visible Range. ACS Applied Optical Materials, 2(10), 2092-2100
Open this publication in new window or tab >>Phototransistors of Engineered InGaZnO Channel for Specific Molecular Detection in the Visible Range
Show others...
2024 (English)In: ACS Applied Optical Materials, ISSN 2771-9855, Vol. 2, no 10, p. 2092-2100Article in journal (Refereed) Published
Abstract [en]

Fluorescence-based single-molecule detection has been widely investigated and applied in biosensing and bioimaging due to its ultrahigh sensitivity and specificity. However, bulky and expensive commercial fluorescence microscopes are usually required. The Stokes shift property of most commonly used fluorophores requires optical sets such as dichroic mirrors and specific filters in the optical pathway before a photodetector to eliminate excitation and scattering lights from the fluorescence signals. The fluorescence signal collected by an objective is further unavoidably attenuated, and the optical resolution is diffraction-limited. Herein, a proof of concept of a lab-on-a-chip compatible molecular sensor is shown by integrating upconversion nanoparticles (UCNPs) and amorphous hydrogen-doped InGaZnO (InGaZnO:H) thin-film phototransistor (IGZO:H TFTs) aiming to alleviate those issues. Upon illumination with a 980 nm infrared light, the phototransistor shows no photocurrent without UCNPs but yields a high photocurrent with UV–visible fluorescent light emitted from the UCNPs. The molecular detection is enabled by further involving the Förster resonance energy transfer (FRET) mechanism, with the UCNPs as donors. The photocurrent falls back to its original low level when biotinylated gold nanoparticles are added to selectively bind and quench the UCNPs via biotin–streptavidin coupling. Each UCNP shows an estimated photocurrent-to-dark current ratio of 103 and each biotinylated gold nanoparticle causes at least 1 order of magnitude decrease of the photocurrent. Our integrated setup presents a promising platform for further development toward an optoelectronic biosensor capable of single-molecule detection.

Place, publisher, year, edition, pages
American Chemical Society (ACS), 2024
Keywords
a-IGZO thin film, phototransistor, upconversion nanoparticles, Förster resonance energy transfer, specific biosensing
National Category
Electrical Engineering, Electronic Engineering, Information Engineering Nano Technology Condensed Matter Physics
Identifiers
urn:nbn:se:uu:diva-538766 (URN)10.1021/acsaom.4c00310 (DOI)001371207800001 ()2-s2.0-85205727031 (Scopus ID)
Funder
Swedish Research Council, 2019-00207
Available from: 2024-09-19 Created: 2024-09-19 Last updated: 2025-01-20Bibliographically approved
Johansson, T. (2024). Uppsalas studenter utbildas på öppna EDA-cerktyg. Elektroniktidningen (9), 12-13
Open this publication in new window or tab >>Uppsalas studenter utbildas på öppna EDA-cerktyg
2024 (Swedish)In: Elektroniktidningen, ISSN 1102-7495, no 9, p. 2p. 12-13Article in journal (Other (popular science, discussion, etc.)) Published
Place, publisher, year, edition, pages
Elektroniktidningen Sverige AB, 2024. p. 2
National Category
Other Electrical Engineering, Electronic Engineering, Information Engineering
Identifiers
urn:nbn:se:uu:diva-549231 (URN)
Available from: 2025-01-31 Created: 2025-01-31 Last updated: 2025-02-03Bibliographically approved
Organisations
Identifiers
ORCID iD: ORCID iD iconorcid.org/0000-0003-3151-5640

Search in DiVA

Show all publications