Logo: to the web site of Uppsala University

For evaluating the power quality in primary frequency control for hydroelectric generating units, the power response time is an indicator which is of main concern to the power grid. The aim of this paper is to build a suitable model for conducting reliable simulation and to investigate the general rules for controlling the power response time. Two huge hydropower plants with surge tank from China and Sweden are applied in the simulation of a step test of primary frequency control, and the result is validated with data from full scale measurements. From the analytical aspect, this paper deduces a time domain solution for guide vane opening response and a response time formula, of which the main variables are governor parameters. Then the factors which cause the time difference, between the power response time and the analytical response time of opening, are investigated from aspects of both regulation and water way system. It is demonstrated that the formula can help to predict the power response and supply a flexible guidance of parameter tuning, especially for a hydropower plant without surge tank.

Currently, the Thoma criterion is often violated to diminish the cross-section of the surge tank; therefore, the surge fluctuation is aggravated and the frequency stability becomes more deteriorative. The focus of this article is on stabilizing the low-frequency oscillation of an isolated hydropower plant caused by surge fluctuation. From a new perspective of hydropower plant operation mode, frequency stability under power control is investigated and compared with frequency control by adopting the Hurwitz criterion and numerical simulation. In a theoretical derivation, the governor equations of frequency control and power control are introduced to the mathematical model. For numerical simulation, a governor model with a control mode switch-over function is built. The frequency oscillations under frequency control, power control, and control mode switch-over are simulated and investigated, respectively, with different governor parameters and operation cases. The result shows that the power control has a better performance on frequency stability at the expense of rapidity compared with the frequency control. Other recommendations regarding worst operation cases and choice of control modes are also developed.

This paper presents a mathematical model of hydro power units, especially the governor system model for different operating conditions, based on the basic version of the software TOPSYS. The mathematical model consists of eight turbine equations, one generator equation, and one governor equation, which are solved for ten unknown variables. The generator and governor equations, which are different under various operating conditions, are presented and discussed in detail. All the essential non-linear factors in the governor system (dead-zone, saturation, rate limiting, and backlash) are also considered. Case studies are conducted based on one Swedish hydro power plant (HPP) and three Chinese plants. The simulation and on-site measurements are compared for start-up, no-load operation, normal operation, and load rejection in different control modes (frequency, opening, and power feedback). The main error in each simulation is also discussed in detail. As a result, the model application is proved trustworthy for simulating different physical quantities of the unit (e.g., guide vane opening, active power, rotation speed, and pressures at volute and draft tube). The model has already been applied effectively in consultant analyses and scientific studies.

Nowadays the importance and need of primary frequency control of hydro power units are significantly increasing, because of the greater proportion of intermittent renewable energy sources and more complex structure of power systems. It brings a problem of increasing wear and tear of turbines. This paper studies this problem by applying numerical simulation and concise theoretical derivation, from the point view of regulation and control. Governor models under opening and power feedback mode are built and validated by measurement data. The core index, guide vane movement, is analyzed based on ideal sinusoidal frequency input and real frequency records. The results show the influences on wear and tear of different factors, e.g. governor parameters, power feedback mode and nonlinear governor factors.

Nowadays, the wear and tear of hydropower turbines is increasing, due to more regulation movements caused by the increasing integration of intermittent renewable energy sources. In this paper, a controller filter is proposed as a solution to the tradeoff between reducing the wear of turbines and maintaining the regulation performance and thereby the frequency quality of the power systems. The widely used dead zone is compared with a floating dead zone and a linear filter, by time-domain simulation and frequency-domain analysis. Simulink models are built and compared with onsite measurement. Then, the time-domain simulation is used to investigate the guide vane movement, the load disturbance and the power system frequency, based on a one-day grid frequency datameasured in this study. In the theoretical analysis, the describing functions method and the Nyquist criterion are adopted to examine the stability of the system with different filters. The results show that the floating dead zone, especially the one after the controller, has a better performance than the dead zone on both the wear reduction and frequency quality. The linear filter has a relatively weak impact on both guide vane movements and the frequency quality. Other related conclusion and understandings are also obtained.